Pebbled 12 mm shank button for German caps and other headgear, painted in black colour. The button is assembled from three parts (front of aluminum, rear and the leg of brass/copper). Button bears no stamps.Price for 1 pc. You usually need 2 pcs. for 1 cap...
2.25 €
Hooks for German soldier waist belts. High-quality copies, we install the same hooks on belts of our own production. Pay attention to the quality stiffening ribs on our hooks. Stiffeners were present on all early hooks until the late model appeared (there were no stiffeners on it).But in the modern copy market, unfortunately, early hooks without stiffening ribs are widespread. These are useless and simplified fakes! To get those stiffening ribs, you need serious pressing and stamping equipment, which is not available to artisans. And they save, they carve their metal crafts and simply bend. Such a copy is not suitable for reenactment.Trust professionals, buy the right hooks here in the "Replika".We offer hooks made of aluminum (production ceased in 1940) and steel (produced 1940-..
9.00 €
Pebbled 12 mm shank button for German caps and other headgear. Assembled from three parts (front, rear and the leg). The front part is aluminium (white metal). The back of the leg and brass/copper. Button bears no stamps. Price for 1 pc. You usually need 2 pcs. for 1 cap...
1.35 €
A copy of the grommet, which was used in the German army to strengthen the cord-holes on the equipment. It has an inner diameter of 17 mm and an outer diameter of about 32 mm, which corresponds to a small grommet on a tent (Zeltbahn).Grommets for the army were made of aluminum or zinc. Later made of galvanized steel. Aluminum and zinc (early) ones are the hardest to get today, reenactors often replace them with modern steel ones. This grommet is more suitable for use in reenactment.Price for 1 grommet + washer (for 1 hole with a clearance of 17 mm). The installation device is sold separately.Take a look at the photo below comparing the original grommet and our copy.The photo above shows the original grommet.Our copy of the grommet...
0.90 €
A very rare copy: a button of reduced diameter, which was used on the pockets of the SS uniform before the war (and on service uniforms during the war). It could also be used for shoulder boards (because the diameter is similar to special screw-buttons). The diameter of 16 mm, it is slightly smaller than the usual uniform, but slightly larger than the button for the caps.The button is made of two aluminum halves, EXTRA FEIN is inscription below, the leg is copper. Tip: the foot can be covered with silver paint so that it does not stand out...
1.12 €
A copy of the grommet, which was used in the German army to strengthen the cord-holes on the equipment. It has an inner diameter of 9 mm and an outer diameter of about 19 mm, which corresponds to a small grommet on a tent (Zeltbahn), or on any type of army backpack.Grommets for the army were made of aluminum or zinc. Later made of galvanized steel. Aluminum and zinc (early) ones are the hardest to get today, reenactors often replace them with modern steel ones. This grommet is more suitable for use in reenactment.Price for 1 grommet + washer (for 1 hole with a clearance of 9 mm). The installation device is sold separately.Take a look at the photo below comparing the original grommet and our copy.The photo above shows the original grommet.Our copy of the grommet...
0.18 €
A metal device for installing grommets (respectively to the diameter). It consists of an upper and a lower part. Allows you to roll the grommets both manually and with a press.To prevent the grommet from crumpling during installation, the height of the cylinder should be 25% greater than the thickness of the fabric (no more)...
18.00 €
This German aluminum uniform button is a replica of a 19mm button used in the Third Reich for various military uniforms.The buttons are unpainted and unmarked. A number (in Arabic numerals) from 1 to 9 is stamped on the top of the button, with 6 and 9 being different buttons (they have a dot next to the number to differentiate them). Custom numbers are available upon request, but the price will be double, with a two-month wait.These are very high-quality aluminum buttons, consisting of three parts: a top, a bottom, and a shank (just like the originals). Cheaper copies are usually cast entirely from similar alloys, not aluminum. Our replica is practically museum-quality; it will be very difficult to distinguish it from the original after aging.Price per pair (2 buttons with the same number)..
13.50 €
Plastic jar, resistant to paint, solvents and alcohol. Suitable for food as a disposable container. PET plastic 1 (Polyethylene terephthalate). The range of application is huge. Volume 40 ml. Height with cover 58 mm, base diameter 42 mm...
0.28 €
The button is assembled from three parts: top, bottom and leg. Buttons are painted in a dark shade of feldgrau. Button has no manufacturer's stamp.German uniform button made of aluminum - the copy of the 19 mm button, which was used in the Third Reich for a variety of military uniforms.The buttons are dyed in the dark field grey. Buttons without marks. On the upper side of the button, a number (in Arabic numeral) from 1 to 9 is embossed, and 6 and 9 are different buttons (they have a dot next to the number to distinguish them). Other numbers can be ordered, but the price will be twice as high, the waiting time is 2 months.Buttons of very high quality, made of aluminum, consist of three parts: top, bottom and stem (just like the original ones). Cheap copies are usually cast entirely f..
13.50 €
German uniform button made of zinc alloy, the copy of the standart German 19 mm button. It's made by mold. The button has on the reverse side convex letters R.P.K.Price for 1 pc. These buttons also have a wholesale price for a quantity of 100 pcs.We sell buttons in three colors:- feldgrau (pale green, close to the color of a field jacket) — buttons were painted in this color until 1940, they could be used until the middle of the war (1943);- dark grey (often it still glistened hideously) — this color was used for buttons after 1942 (as well as for M42 helmets);- without paint (gray-silver color of metal) — buttons could be unpainted (especially on the uniform of officers), and unpainted buttons can be independently painted white for winter uniforms.Please choose th..
0.36 €
German uniform button made of aluminum with a diameter of 19 mm. The button is assembled from several stamped parts, just like the original one. Suitable for officer uniforms or for painting in different colors as needed...
0.90 €
German uniform button made of brass with a diameter of 19 mm on the leg. Suitable for the uniforms of generals, as well as naval officers and various party organizations.A modern copy...
0.90 €
Buttons from German field jackets, original. There is corrosion, oxides. Different stamps of the 1930s and 1940s. There are zinc and aluminum.We'll try to collect a set with the same metal and stamp for you! Please ask in the comment when ordering.Buttons require careful cleaning before use. It cannot be subjected to strong machining, since, for example, white spots on zinc or aluminum with strong machining can turn into holes that will have to be filled with putty or resin with aluminum powder. It is assumed that the buttons, after easy cleaning and alignment, will be painted on top in the Feldgrau colour, after which they will start to look good. If you are not going to paint them, if you need a perfect result, then you need to buy copies of such buttons or mint originals (good mint orig..
0.49 €
German uniform granulated button made of aluminum with the leg (shrank), diameter 22.5 mm. Suitable for officers uniforms. If you paint it in feldgrau or white, it is suitable for winter clothes (jackets, overcoats).The leg is made of copper, the button itself is assembled from two extruded parts of aluminum. Modern copy...
1.08 €
German uniform button made of aluminum with a diameter of 22 mm on the leg. It is suitable for overcoats, winter clothes. It's slightly larger than the one used on soldiers' field jackets.The leg is made of copper, the button itself is assembled from two stamped aluminum parts. A modern copy.The price is for 1 button...
0.90 €
Diameter 13 mm — for fastening a sleeve on a jacket, inside pockets (for a first aid pocket on a tunic, for example) for internal fasteners on trousers. Gorgeous quality copy of the button for field jackets and pants, Panzer uniforms etc. Color black or field gray on your choice.Price for 1 button...
0.90 €
Diameter 16-17 mm — for pockets, shoulder straps, various straps (for example, to hold the overcoat collar in a raised position). Gorgeous quality copy of the button for winter double-sided jackets, windjackets of mountain troops, camouflage overalls of the SS, camouflage jackets of the Luftwaffe, Panzer uniforms.Color to choose from: black or brown.Price for 1 button...
0.99 €
Original German flat buttons "plates" with 4 holes made of metal. Such buttons were used for German uniforms during The First and Second world wars. They were sewn on camouflage blouses, shirts, pants (both cloth and HBT) and overalls of all kinds. In general this button is a classic, it can be used on any clothing.The diameter is 17 mm. Material: zinc. The buttons are only washed (not cleaned mechanically). The condition can be seen in the photo: the surface may not be completely smooth, but there are no holes or rotten edges. A little care (with the help of a sand-paper) will dramatically improve the appearance.The original buttons could be painted (usually gray or green), you can paint them yourself to give them a new look. Buttons made of non-ferrous metal do not deteriorate from washi..
0.11 €
These flat buttons were used for German uniforms during The First and Second world wars. They were sewn on camouflage blouses, shirts, pants (both cloth and HBT) and overalls of all kinds. In general this button is a classic, it can be used on any clothing.The diameter is 17 mm. We offer buttons made of aluminum and steel (steel buttons are painted gray) and zinc coated steel (silver color, look like zinc, but stronger).Original buttons, by the way, were rarely zincated. By the time the buttons started to be made of steel (1940), it was not possible to use expensive zinc for finishing such minor items as buttons. So they just painted buttons in gray. You need to remember that the clothes on front did't live long (as well as soldiers), so rusty buttons were not a problem there.Our replica s..
0.63 €
A very good copy of buttons for officers' shoulder boards. Made of 4 parts: the base, the cover with a granular surface, threaded leg and nut, that should be sewn to the uniform. Diameter is 17 mm, a little less than buttons for field blouse, as it should be.We offer buttons for officers (silver) and generals (gold). If silver is not available, then you can take gold and paint them.Price per pair, sold in pairs...
13.50 €
Metal buttons (17 mm diameter) with three holes for fastening. We offer steel and aluminum buttons, choose the material before order...
0.63 €
Original German three-hole buttons "plates" made of non-ferrous metal. Diameter 17-18 mm. The buttons are only washed (not cleaned mechanically). The condition can be seen in the photo: the surface may not be completely smooth, but there are no holes or rotten edges. A little care (with the help of a skin) will dramatically improve the appearance. Buttons made of non-ferrous metal do not deteriorate from washing, but on the contrary get cleaned!We offer zinc and aluminum, choose the material before ordering. If you find no metal you want there, then it is sold out.Zinc ones are less common. Aluminum usually looks better. If you have high requirements, then take a little more buttons than you need to choose yourself...
0.11 €
Diameter 22 mm. Superb quality copy of the button for winter double-sided jackets, windjackets of mountain troops, camouflage overalls of the SS, camouflage jackets of the Luftwaffe, Panzer uniforms.Color to choose from: feldgrau (dark dull green), black or brown.Price for 1 button...
0.99 €
Diameter 22 mm. Superb quality copy of the button for winter double-sided jackets, windjackets of mountain troops, camouflage overalls of the SS, camouflage jackets of the Luftwaffe, Panzer uniforms. Made of resin like the originals (not plastic, like many modern buttons).Color to choose from:green — perfectly matches the color of mountain windbreakers, can be used with camouflage uniforms, on padded winter suits;blue-gray — for Luftwaffe uniforms, winter suits of the Wehrmacht, SS, Luftwaffe;white — for any winter uniform, the color is not snow-white, but dirty (grayish), so as not to stand out on the original uniforms or on the correct copies.Price for 1 button. Comparison of our copies and original buttons. White buttons: a copy at the top and bottom, others are original. Blue-gre..
0.70 €
Black buttons (pins) for German peaked-caps of enlisted men and NCO's. These attach the strap to the peaked-cap.Price per piece (you need 2 pcs. for 1 cap)...
2.25 €
Price is for 1 button. You need usually 2 buttons for a cap. Brown buttons with a diameter of 13 mm, made of hard wood, which imitates the original buttons as closely as possible in texture and color. Such buttons at the beginning of the 20th century were usually made from Coroso walnut. They served as a distinctive feature of Jaeger caps in the initial period of the war. Rare item! Later, all the buttons were already metal...
5.40 €
Price is for 1 button. You need usually 2 buttons for a cap. Buttons of brown color, diameter of 13 mm from synthetic polymer. Such buttons served as a distinctive feature of the Jäger caps in the initial period of the war. A rare thing! Later, all the buttons were metal...
1.12 €
Gold buttons (pins) for German officer peaked-caps. These attach a twisted metal cord to the peaked-cap. Gold for generals (silver were for officers, respectively). Rarely found.Price per 1 piece (you need 2 pcs. for 1 cap).Silver ones you can buy also from us!..
2.25 €
Gold buttons (pins) for German navy (Kriegsmarine) peaked-caps. These attach a cord (chinstrap) to the peaked-cap. Very rarely found.Price per 1 piece (you need 2 pcs. for 1 cap)...
2.25 €
Silver buttons (pins) for German officer peaked-caps. These attach a twisted metal cord to the peaked-cap. Silver for officers.Price per 1 piece (you need 2 pcs. for 1 cap)...
2.25 €
Black painted genuine leather strap for peaked-caps of privates and non-commissioned officers of the Heer. Very high quality. Sold without buttons...
16.20 €
The golden cord was worn on generals' peaked caps of the Heer, the SS and the Luftwaffe (and other branches). The officers had silver cords.The cord is made of metal thread, it feels cold. Very good copy.Buttons (pins) are not included! Buttons are sold separately...
20.70 €
The silver cord was worn on officers' peaked caps of the Heer, the SS and the Luftwaffe, and was also used on peaked-caps of other branches. The generals had golden cords.The cord is made of metal thread, it feels cold. Very good copy.Buttons (pins) are not included! Buttons are sold separately...
18.00 €
There is a missing fixation element on one side. It can be used if it is simply sewn with thread or fixed with glue.The silver cord was worn on officers' peaked caps of the Heer, the SS and the Luftwaffe, and was also used on peaked-caps of other branches. The generals had golden cords.The cord is made of metal thread, it feels cold. Very good copy. Buttons (pins) are not included! Buttons are sold separately...
9.00 €
Metal (brass) eyelet for edging vents in German side-caps, field caps. Enamel painted in the correct color. The kit includes a washer for fastening from the inside. A manual press is used for installation, however, it is easy to fasten the eyelet manually (because it is quite soft) with a blunt round object as a rig.The inner diameter of 3 mm, the outer 7-8 mm.Price for one piece. You need 2 pcs. for a side-cap, 4 pcs. for a field cap (depending on model).Comparison of grommets with an inner diameter of 5 mm (two pairs on the left) and 3 mm (on the right)..
0.22 €
Metal (brass) eyelet for edging vents in German side-caps, field caps. Enamel painted in the correct color. The kit includes a washer for fastening from the inside. A manual press is used for installation, however, it is easy to fasten the eyelet manually (because it is quite soft) with a blunt round object as a rig.The inner diameter of 5 mm, the outer 10 mm.Price for one piece. You need 2 pcs. for a side-cap, 4 pcs. for a field cap (depending on model)...
0.18 €
Metal (brass) eyelet for edging vents in German side-caps, field caps. Enamel painted in the correct color. The kit includes a washer for fastening from the inside. A manual press is used for installation, however, it is easy to fasten the eyelet manually (because it is quite soft) with a blunt round object as a rig.The inner diameter of the grommet is 3 mm, the outer 7-8 mm.Price for one piece. You need 2 pcs. for a side-cap, 4 pcs. for a field cap (depending on model).Comparison of grommets with an inner diameter of 5 mm (two pairs on the left) and 3 mm (on the right)..
0.22 €
Metal (brass) eyelet for edging vents in German side-caps, field caps. Enamel painted in the correct color. The kit includes a washer for fastening from the inside. A manual press is used for installation, however, it is easy to fasten the eyelet manually (because it is quite soft) with a blunt round object as a rig.The inner diameter of 5 mm, the outer 10 mm.Price for one piece. You need 2 pcs. for a side-cap, 4 pcs. for a field cap (depending on model)...
0.18 €
A copy of the tape, which was used as a belt and cuff-straps on winter jackets of the Wehrmacht and SS. The width of the tape is 3 cm, the tape is pale green on one side and white on the other. Woven tape is made as a whole piece, and not sewn from two pieces of different colours, as on cheaper copies. The ends of the tape were usually tucked 2 times and sewn with a longitudinal stitch. At the end of the war (especially on SS jackets), the ends were tucked 1 time and secured with a zigzag seam directly along the cut.The tape was not a rigid strap, it was just a tape, quite soft and thin, so that it could pull off the jacket, but so that it did not disturb under the waist belt.Price is for 1 meter. You need from 1.6 to 2.5 meters for 1 winter jacket, depending on the size and whether y..
1.36 €
Woven cotton rope 4 mm thick. Used by German industry in winter clothing and equipment (backpacks). Similar cords were used by other countries in the world in the middle of the twentieth century.Price per meter, you can buy any length, but the rope is already cut off by 10 meters!..
0.45 €
If you need additional photos of the product, write to us by email or in the messenger.A copy of SS/RZM paper tag for the SS clothes, headgear and insignia. It gives a nice completed look to items. It was usually glued or sewn on the back or invisible side of the item. Batch number was written or stamped with ink on the lines. We have a real ink stamp (number 16.). Numbers and letters indicate the type of product.Size 2x4 cm or ¾х1½ in...
1.30 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us by email or in the messenger.A copy of the cloth tag for SS clothing and equipment. It will give an entourage look to collectible items. It was usually glued or sewn onto the back or invisible side of the object. It is written Vom Reichsführer SS befohlene Ausführung, that is, "Exe..
6.30 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us by email or in the messenger.Proven quality stamps. We use similar stamps by ourselves accepting goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are desi..
12.60 €
Proven quality stamp. We use such by ourselves when take goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to work with water-based inks, and quickly get out of order from other inks. And our stamps allow you to use alcohol and solvent based paints and are designed for long use.Price for any stamp, for 1 pc. The price depends on the size of the stamp. We offer the following standard stamps for Soviet military clothes:• Year 1941. A stamp for the Red Army clothes "Sewing Factory named after the 23rd anniversary of the October", year 41. By the way, there were a lot of factories and artels named after some kind of anniversary of October throughout t..
5.40 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us by email or in the messenger.Proven quality stamps. We use such by ourselves when take goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to wo..
6.30 €
Proven quality stamps. We use such by ourselves when take goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to work with water-based inks, and quickly get out of order from other inks. And our stamps allow you to use alcohol and solvent based paints and are designed for long use.Price for any stamp, for 1 pc. The price depends on the size of the stamp. We offer the following standard stamps for making M24 and M39 grenade maquettes:• The inscription VOR GEBRAUCH SPRENGKAPSEL EINSETSEN in direct font for the "head" of the German hand grenade, approximately 7×3 cm in size.• The same thing, but in serif font, another popular type of this inscript..
10.80 €
Proven quality stamps. We use such by ourselves when take goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to work with water-based inks, and quickly get out of order from other inks. And our stamps allow you to use alcohol and solvent based paints and are designed for long use.We offer the following stamps for the Third Reich uniform:• Stamp VA 1939 was used on SS clothing at the beginning of the war. Size approximately 5×3 cm.• SS-BW stamp (SS-Bekleidungwerke, SS sewing enterprises) met on SS clothing during the war. Size approximately 5×2 cm.• RB.Nr. with numbers (code) of the manufacturer, such stamps were used on clothes after 1943. Size approxim..
5.40 €
Proven quality stamps. We use such by ourselves when take goods to the warehouse.Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to work with water-based inks, and quickly get out of order from other inks. And our stamps allow you to use alcohol and solvent based paints and are designed for long use.We offer the following stamps for the Third Reich uniform:• Stamps with Roman numerals (I, II, III) were usually used on Wehrmacht uniforms (winter jackets and other things that were produced only in three sizes). The height of the digits is approximately 1.5 cm.• Stamps in Arabic numerals (1, 2, 3) were usually used on SS uniforms (the Luftwaffe used both, depending on the man..
4.50 €
Size stamps that were usually placed on the leather petals of liners for German helmets. Can be used for any headwear in any form.Proven quality stamps. We use such by ourselves when take goods to the warehouse. Be careful, do not be fooled! Our stamps are made from rubber, not from a cheap disposable material that is commonly used to make office seals. The seals are designed to work with water-based inks, and quickly get out of order from other inks. And our stamps allow you to use alcohol and solvent based paints and are designed for long use.Price for any stamp, for 1 pc. We sell each size separately, not all together!Stamps that are in stock can be selected next to the Add to Cart button. If they are not in the list, it means that they are sold out and will be later. We can also m..
5.40 €
Steel stamp (marker) of the Third Reich military acceptance bureau, number 77. Eagle wingspan 4 mm. The letters WaA are missing. This is a very small stamp, which was found on the details of the bayonet to the Mauser carbine and small details to weapons, ammunition. In general, the stamp of military acceptance was applied to all items that were related to the weapon and its accessories. On weapons and ammunition (that is, on particularly important military items), the acceptance stamp was applied to every detail, sometimes even several times.The height of the handle (finger) is about 10 cm. To work with a blow to steel and other metals, leather, wood. Hardness according to GOST 25727-83 from 55 to 62HRC. The brand is hard-tempered, you can work on the details of weapons and tools with hard..
49.50 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us to email or messenger.Steel stamp (marker) of the Third Reich military acceptance bureau (Waffenamt, abbreviated WaA): letters WaA and the number 518 of the checking officer. Eagle wingspan 5 mm. This stamp can often found on the details of the bayonet to the Mauser carbine, for ex..
49.50 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us by email or in the messenger.Steel stamp (marker) with SS runes for forging dog-tags of the Third Reich. Runes are 5 mm height.The height of the handle (finger) is about 10 cm. To work with a blow to steel and other metals, leather, wood. Hardness according to GOST 25727-83 from 55..
49.50 €
Steel stamp (marker) of the Third Reich military acceptance bureau (Waffenamt, abbreviated WaA): letters WaA and the number 39 of the checking officer. Eagle wingspan 4 mm. This stamp can often found on the details of the bayonet to the Mauser carbine, for example. A stamp of military acceptance was applied to all items that were related to the weapon and its accessories. On weapons and ammunition (that is, on particularly important military items), the WaA stamp was applied to every detail, sometimes even several times.The height of the handle (finger) is about 10 cm. To work with a blow to steel and other metals, leather, wood. Hardness according to GOST 25727-83 from 55 to 62HRC. The brand is hard-tempered, you can work on the details of weapons and tools with hardness up to 43HRC. Don'..
49.50 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us by email or in the messenger.Steel stamp (marker) with the emblem of the Third Reich (eagle and swastika in its claws). Wingspan of the eagle is 8 mm. The most often this design can be found on German weapon parts or ammunition.Handle height is about 10 cm. To work with a blow to s..
72.00 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us to email or messenger.Steel stamp (marker) of Waffenamt (or WaA) of the Third Reich. Letters WaA and marker's number 123. This stamp is copied from the bottom (cap) of the M24 grenade. It is quite small 7×5 mm.The height of the handle (finger) is about 10 cm. To work with a blow to..
63.00 €
This product is intended for military-historical reenactment (immersive stydy of history); for creating costumes for theatrical and film, video plays condemning Nazism and fascism; as well as for exhibiting in museums of military history. This product is not propaganda of ideas and criminals convicted by an International Military Tribunal, and should not be used for such a purpose! The photos have been edited in accordance with the requirements of the law.If you need additional photos of the product, write to us to email or messenger.Steel stamp (marker) of Waffenamt (or WaA) of the Third Reich. Letters WaA and marker's number 159, wingspan of the eagle 9 mm (total width with letters is 10 mm and height 9 mm). The most often this design can be found on large German weapon parts, i. e. MG m..
63.00 €
Exact and high-quality copy of the hook for the SS helmet cover. Includes a black hook, spring and rivet. You need 3 hooks for 1 cover. Price for 1 hook, spring and rivet kit...
6.30 €
There is no size stamp on the rim on sizes 55, 56 (only an ink stamp on the leather). The brand of the manufacturer is on all the liners.A copy of the German liner. The sizes are accurate and the materials are carefully selected. Aluminum bands, 1.5 mm leather, beige or brown felt. On the sides of the band are size stamps (for example, 58/66 n. A., where 58 is the size of the head, and 66 is the size of the helmet). Size stamp is embossed on the inner rim also. The inner rim of the steel spring (Balaclava transition period of 1940, when often used parts made of aluminum and steel in the same product)! There is also the name of the manufacturer on the band (BERL. KOFFERFABRIK MAX DENSOW, a suitcase factory in Berlin is not the most popular, but one of the first manufacturers of these l..
40.50 €
The rims are reinforced, it's the most common option in the late 1930s with an additional plate in the ear area.The rims size 66 are not reinforced as in the photo.Outer rim for M31 German liner for M35 helmets, suitable for M40. Made of aluminium, it comes unassembled, which allows you to assemble it together with other parts without stuffing them, without the risk of damage.Rivets for assembly (requires 2 pieces) are sold separately (see Featured Products below). Earrings for the chinstrap are not riveted and are not included. They can also be purchased separately.Our "constructor" allows you to repair original liners by replacing them piece by piece.No labels. Without side reinforcements (early model)...
24.30 €
One rim 66/59 has a dimensional stamp, assembled as a ring by a rivet.Inner rim for M31 German liner for M35 helmets, suitable for M40. Made of aluminium, it comes unassembled, which allows you to assemble it together with other parts without stuffing them, without the risk of damage. Aluminum spring.Rivets for assembly (requires 2 pieces) are sold separately (see Featured Products below). Springs and rivets can also be purchased separately from us.Our "constructor" allows you to repair original liner by replacing them piece by piece.No manufacturer's marks...
13.50 €
Split-pins attach the liner to the sphere of the helmet to get a complete helmet. These pins often break on original helmets during disassemble process, so they are replaced with copies.The stamps inside the legs on the LB38, 1939 and IKA40 models. The rest have stamps on the outside of the legs! The manufacturer's stamps were found both inside and outside.The stamp is on the outside of the legs: examples on the website german-ww2-helmet.comThe stamp is inside: examples on the germanhelmetvault.comOur split-pins are made on factory machinery and are copies of museum quality. They are very difficult to distinguish from originals if a person does not understand the stamps and the production history of the German helmets. Brass clasps are made entirely of br..
10.80 €
Price is per set (3 pieces).Split-pins attach the liner to the sphere of the helmet to get a complete helmet. These pins often break on original helmets during disassemble process, so they are replaced with copies.The stamps on the outside of the legs! The manufacturer's stamps were found both inside and outside.The stamp is on the outside of the legs: examples on the website german-ww2-helmet.comThe stamp is inside: examples on the germanhelmetvault.comOur split-pins are made on factory machinery and are copies of museum quality. They are very difficult to distinguish from originals if a person does not understand the stamps and the production history of the German helmets. Steel split-pins are made entirely of steel and are covered with a chem..
10.80 €
Chin-strap with aluminum parts to German helmet M35. It is made to complete a set of original helmet of a museum copy. Waxed linen thread is used. The flesh-colored skin of which the strap is made was aged to look like the original.Made exclusively for the shop "Replika"! Very similar to the originals.The original straps with these stamps, the drawing of the stamps, and what do such plates with a stamp look like, are shown below.We offer such straps with the stamps of Wilhelm Eilers jr. Bielefeld 1936 и FRANZ BREHME 1938. Both are an exact copies of the original stamps, such stamps actually existed and are found in collections.The stamp must be selected before ordering next to the "Add to cart" button. If some option is not there, then such ones are currently sold out.How to install the st..
22.50 €
Strap for German M35 or M40 helmet with aluminum buckle and pins. Tight leather of skin colour, waxed thread. These straps are made exclusively for Replika shop. High quality. Stamped Wilhelm Willers Jn. Bielefeld 1936 (copy of the original stamp).The strap is installed so that the buckle is on the left cheek, and the tips are turned outward (so that the beige skin can be seen from the outside). Remember that the bosses are designed for a single connection, that is, it will be impossible to unbutton the boss without damaging the skin...
17.10 €
Chin-strap with steel parts to German helmet M40 or M42. It is made to complete a set of original helmet of a museum copy. The flesh-colored skin of which the strap is made was aged to look like the original. Waxed linen thread is used. All accessories are fined manually and painted in gray color, then they were artificially aged. Made exclusively for the shop "Replika"! Very similar to the originals.The original straps with these stamps, the drawing of the stamps, and the plates themselves are shown below.We offer such straps with the stamps of dfc42 and G. SCHIELE LOBURG 1941. Both are an exact copies of the original stamps, such stamps actually existed and are found in collections.The stamp must be selected before ordering next to the "Add to cart" button. If some option is not there, t..
22.50 €
Strap to the German helmet M40 or M42 with a steel buckle and bosses. The steel fittings are painted in light gray, as it was in the original. Thick flesh-colored leather, waxed thread. Made exclusively for the Replica store! Very high quality.We offer straps with various brands for the Wehrmacht and SS. Select the brand next to the "Add to cart" button. If there is no brand, then these straps are sold out.The strap is set so that the buckle is on the left cheek, and the tips are turned out (so that the light skin can be seen from the outside). Remember that the bosses are designed for a single connection, that is, it will be impossible to unbutton the boss without damaging the skin...
17.10 €
Bosses (lugs) are needed to attach the strap to the earrings of M31 German helmet liner.We have aluminum and steel lugs for your choice. The material must be selected next to the "Add to cart" button. If you can't see any material there, then it is sold out.Price for 1 pc. One helmet usually need 2 pcs...
3.15 €
Buckle to the chin strap for a German helmet, replica. Made of aluminium, stamped...
7.20 €
Buckle to the chin strap to a German helmet, replica. Made of steel, with anti-rust treatment. The original buckles were often painted light gray. We sell non-painted buckles...
7.20 €
Leather detail to the M31 German helmet liner. It consists of leather and a strip of felt (you don't need to buy extra felt, although it is sold from us as a separate product). The thickness of the skin is 1-1.4 mm, the thickness of the felt is about 1.5 mm. Felt can be almost white or gray, gray-brown. It is completed with a cord of the correct thickness. Lace made of artificial materials, do not be shy about this, because the original laces were also not completely natural (the Germans just understood the advantages of synthetic materials and actively introduced them).Fits all sizes (length 62 cm, 9 petals). To get the right size, you need to cut off the extra length and sew the skin into a ring. Then you need to tighten the skin on the rim when wet and fix it with metal legs (sold separ..
9.00 €
6.75 €
Cotters: part of the German helmet liner, these hold the leather detail on the inner rim of the liner.We offer cotter pins made of the following materials:• Aluminum for early M31 liners and transition models up to 1940 (including).• Galvanized (zincated) steel for M31/40 liners with steel rims and transition models from 1940 onwards.Price for 1 piece. One liner needs 11-13 pieces (depending on the size of the liner). The material should be selected next to the "Add to cart" button. If there's no material available, so it's sold out...
0.45 €
Earring: detail to а liner of a German helmet, hold the chin strap, attached to the outer rim with a rivet.Material - aluminum (for early M31 liners and transitional models up to 1940 inclusive).Price for 1 piece. You need 2 pieces for one liner...
2.70 €
Cord to the liner of the German helmet made of natural material, woven. Finding a suitable cord for a German helmet liner is rather difficult: often can be found either synthetic or of incorrect thickness. We offer a good quality and not expensive product in two colors: white and beige (select before purchase)...
0.90 €
If there is a cloth or synthetic fabric in your copy of the liner, change it to a good, proper felt!The gray felt is dense, soft, 1 mm thick. The raw material is natural wool, not synthetic! 4×62 cm strips (enough for 1 liner of any existing size). If you need a longer strip (up to 70 cm), specify this in the order comment. It is sewn onto the leather, then the leather is attached with metal splints (paws) to the M31 liner and its modifications...
3.15 €
Spring to the liner of the German helmet (model 1931 that was used in M35, M40 and M42 helmets). Made of spring steel (straightens when bending). Price for 1 piece (you need 5 pcs. for 1 liner).The spring are used to restore an original liner (original springs usually rot or become brittle there). Also to replace low-quality springs in copies of liners (these are usually of wrong size or thickness).Our springs are painted. The original springs were painted at least until the optimization of the helmet production process in 1940. The installation of painted springs in the liners continued until they ended up in warehouses. In helmet liners produced in the middle of the war painted springs almost never occured.The springs were different in length, due to the diameter of the li..
2.52 €
Spring for German helmet liner (1931 model, suitable for M35, M40, M42 helmets). Made of spring steel (straightens when bent). The price is for 1 piece (5 pieces are needed for 1 liner).Such springs are used to restore the original liners (in which the springs usually rot or become brittle). Also to replace low-quality springs in replica liners (they usually have springs of the wrong size or thickness).These springs are not painted. In 1940, in order to reduce costs, they were no longer painted. In liners produced in the middle of the war, painted springs are almost never found.The springs were different in length, due to the diameter of the liner rim. For any diameter of the rim, it was necessary to use 5 springs, therefore, their length changed. There is no table matching the length of t..
2.43 €
Nice aluminum rivets for installing steel springs to inside (soft) band of German helmet liner. Diameter of the leg is 2 mm.Price for 1 piece. You need 5 pcs. for 1 liner.How to install the rivet?To do this, you will need an anvil with a recess in the form of a hemisphere. Ideally, there should be two: for both sides of the rivet, so that the finished hat is not flattened from the blows on a flat anvil. The rivet is cut approximately to the height of the future hat (if the height of the hat is 2 mm, then it can be cut by 2-3 mm, this will become clear during the trial installation and depends on the rivet material). Insert the rivet into a ready aperture, lean a hat on the supporting anvil for support, and on the other hand beat a hammer (or a press) on a rivet through another anvil. The h..
0.04 €
Aluminum rivets, which were common in the twentieth century, and in the XXI century, due to the spread of new connection technologies have become rare.Leg diameter 3 mm, cap diameter 5.5 mm, height of the cap is 2 mm leg length 10 mm. Price for 1 piece.The diameter of the legs 2.5 mm, diameter 3.5 mm hat, hat height 1.5 mm, leg length 8 mm. Price for 1 piece.How to install the rivet?To do this, you will need an anvil with a recess in the form of a hemisphere. Ideally, there should be two: for both sides of the rivet, so that the finished hat is not flattened from the blows on a flat anvil. The rivet is cut approximately to the height of the future hat (if the height of the hat is 2 mm, then it can be cut by 2-3 mm, this will become clear during the trial installation and depends on the riv..
0.09 €
A perfectly executed plate for completing the Mauser bayonet for the 98k carbine. Steel, bluing.It is fixed between the body of the handle and the pads, pressed with two screws. Screws are also sold from us...
9.00 €
Original cardboard box for 10 rounds of ammunition for the MG machine gun, Mauser carbine and other weapons of 7.92 mm caliber. The year 1939 is stamped on the cardboard, and the label says 1940/1...
6.30 €
Original spikes (nails) for German mountain military shoes from the Second World War. Made in Germany before the war. Spikes steel, rust-free, from the original packaging of the 1940s.Designed for the German model of mountain boots (for rangers). They have 3 options:1) on the sole (with a conical head); for 1 pair of shoes you need 50-72 pcs. depending on the padding pattern (and shoe size).2) on the welt (on the edge of the sole, the shape like the head of Mickey Mouse, the short spike), for 1 pair of shoes of size 43 you need 42 pcs. The number of fittings depends on the size of the shoe: it is obvious that the perimeter of the soles of sizes 40 and 46 are different. That is, the number of spikes for the welt can be from 34 to 56 pcs.3) on the heel (on the edge of the heel, the shape lik..
1.62 €
Original hobnails for German military boots of World War 2. Nails are made of steel, not rusty, from original package of 1940-s. 6 facets, one leg.Price for 1 nail...
1.08 €
These wooden pegs are used for assembly (repair) of soles of any shoe model of the early twentieth century and their copies. Including high-boots and lace-boots of the Heer/SS.The section is 2x2 or 2x3 mm, length is about 2 cm, the end is sharpened, the wood is very durable — you can’t break it with your hands. The price is for 1 pc., You can take how much you need...
0.22 €